Also, the projector is supposed to come with little parts of it trimmed of so they fit the stock housing. Man I was so joyed. As a final results that was exactly what I was looking for, Very bright, light goes vary far far away. The kit was shipped quickly, and was not missing any parts upon arrival; in fact, there was a checklist in the package with human checkmarks! It will be your last chance to do so. Has a sharp cut off. No big deal for a dremel. I have an 09 wrx and new lights are crazy expensive! The relay kit i did not have a chance to install but it looks like a good quality set.
It does not matter because on the other side it comes out the same so just the colors are swapped but not the polarity. Need a recommendation on parts for your project? Luckily I was able to sell the foglights fairly quickly locally! I am sick of paying and taking time to drive 45 minutes to the dealer to get this fixed all the time. Checked if all works ok and it does. Do you have a better way than just windex and microfiber towels? I left the lights in during pre-heat so there is less of a shock to the light when adding it at full temp. This continues for no apparent reason. Using the original mounting holes paired with new hardware, they are the beauty behind the kit that makes it an easy install.
Will not be buying anymore Subaru's. With their small framework and compact 2. Everything fits right in and you could really knock out the install pretty quickly if you needed to. A recall needs to be created to fix this issue. I was able to remove all wire components except for the one connected to the low beams and runs at the bottom inside the projector housing through this rubber grommet thing.
I could not see the road and I drove off the side of the road and slammed my brakes on. Was curious if you did any scuffing with high grit sandpaper or steel wool before and used a plastic adhesion promoter before spray painting the piece? At the end there was an area on the bottom where the Bi-xenon solenoid housing would hit, and that also had to be carved out. We did a few color matched housings, but not many. Hopefully it will last long. The original dealer is no longer in business so I took it to a different dealer. Our projector headlights are specifically designed for plug and play easy installation. But again, no color amd i had to fiddle quite some bit to make them work so im a little disappointed.
I wanted to emulate the look of the yellow bulbs in a chrome housing but without actually having yellow bulbs in there. For this, the easy way is to leave all the components together and tape off the housing. In the end its worth the money and time. If we sell it, we use it, and we know it. I didn't know where to find the part I needed for my vehicle, so was very happy to come across your FaceBook page. Illuminates a lot of road all the way to the cut of which is crisp and sharp. This is getting frustrated and I do not hear or see of a recall for the problem.
The light output decrease will depend on how many coats you apply. There is usually enough left from the factory to reseal, but I have to be on the safe side when dealing with customers lights. If not, you can carefully place each of them in the oven to bake. One spot was in the corner where is a insert that is used for light adjusting screw. No, you're not seeing things here, but yes you will be seeing everything at night. Top mod Dan Reviewed: 04. Rotation was spot on, had to align it a little.
Bi-Xenon Projectors: The most compact high performance Bi-xenon projectors from Morimoto. The black will cut slightly more depending on how dark you go. Sure, there's better projectors out there, with better optics, but for the ease of installation, this kit can't be beat. I didn't even bother to test fit the projectors before sealing them up. After these issues were resolved i re-assembled the headlights and installed on the car. Replace the two screws for them. You can put them back in the oven and split again.
I see alot of complaints, but again, no recalls to fix the problem. Overall if your thinking of retrofitting your lights go this route, no guesswork and a great overall product. Let me explain on that one a bit more. Definitely want to do this after seeing yours. Would not call it direct retrofit. Not sure why they keep dying prematurely.